User Guide - Configure LoRa Devices

This user guide applies to Aurora LoRa devices. It will cover how you can configure your devices using Vicotee's USB LoRa Config Gateway.

Table of contents


Vicotee aims to support any type of LoRaWan network out there, that means, that almost all possible network configuration parameters must be exposed to the end user.

For instance, you may run basic setup with Multitech MultiConnect LoRaWAN Gateway, that means the Application EUI and Application Key are fixed and cannot be changed, Hence, our devices need to have the ability to modify their Application EUI and Key during commissioning phase in order to be able to join their network.

Another example, you run a multiple gateways with Loriot solution on top of them, your setup does not allow enrolling devices with specific Application EUI and Key, a unique one-time app key is generated for a given device once it's enrolled into the network, again, we need to adapt and be able to change these parameters on our devices.

Yet another example, you run multiple gateways based on Actility solution, your setup allows enrolling any device with any Application EUI and Key combination, so no additional configuration is required from our devices.

Among these things we also allow customer to further customize our nodes by specifying the type of network (public/private), modify the data rate settings etc and upload specific drivers to achieve a full-blown event driven sensing solution which can lower the overall traffic in the network and lower the total power consumption per device.


USB LoRa Config Gateway


  1. Use a USB cable and connect USB LoRa Config Gateway (hereby: USB Gateway) unit with your computer running Windows 8 or Windows 10.

    The first time you plug the USB Gateway to your computer, it may take several minutes for Windows to auto install the driver. Once the driver is installed, a notification is shown at taskbar.
    USB driver installed
    Windows 10's notification of driver installed and ready to use.


  2. When USB Gateway is connected to your computer, a green light (3) will perform a fast blink (0.5 second) indicating it got power.



USB LoRa Config Gateway Application


  1. Download and install Vicotee USB LoRa Gateway Config application for Windows from Windows can warn the program is unsigned when you start it for the first time. You answer 'yes' or 'Run anyway' to the question if you want to continue to install it.

    Windows Defender
    First time running the software, Windows 10 shows this warning. Click 'Run anyway'.


  2. Once the application is installed, start it and click on "Connect" button. The application will now search for the USB Gateway. If it doesn't find the Gateway, try disconnecting and then reconnect it back to your computer and click "Connect" button.

    Note: The first time you are using USB Gateway; your computer may take a few minutes to install a driver for the Gateway. If the application fails to find your USB Gateway, wait a few minutes and try again.


Basic Settings

The application has two mode: Basic and Advanced.In Basic mode, you can configure your devices with new Application EUI, Application Key and Device EUI. Enter new values you want to configure your device with and click the "Start Scan" button to allow USB Gateway to scan for devices and re-config them. 

Go to "Start The Device In Configuration Mode" section to read more about how to start the devices in configuration mode.

Advanced Settings

You have more advanced options to configure your devices in this Advanced mode.

Caution: You will permanently overwrite the current settings in your device with new values from the application. The device may stop working until the LoRaWAN gateway is configured to accept new settings from devices.

Once the application found the device (in configuration mode), it will send commands through USB LoRa Config Gateway to the device. When configuration is done, the device will reboot itself back to normal mode.


Start The Device In Configuration Mode

Skip step #1 if your device already turn off and go to step #3.

  1. The device can be turn off by placing a magnet near magnetic switch symbol (2) for 30 seconds.

    Figure 2

After 30 seconds, a green light (3) lights up. Remove the magnet as soon as the light comes on. After the magnet is removed, the green light may light for another 5 seconds.

  1. Once the device is off, turn it on by placing a magnet near (2) and hold it until the red light is lit for 3 seconds and then start blinking. Lift off the magnet once the red light blinks. Do not lift off the magnet before the red light is blinking.

  2. You device is now in configuration mode. To indicate it still in configuration mode, the red light will blink once every 5 seconds.


  • The device remains in configuration mode for 10 minutes. If it does not receive commands or messages from the USB Gateway during this period, it will automatically turn off.
  • The device restarts automatically when all commands are received from the USB Gateway. If your intention is only to configure the device and not have it running, be sure to turn off the device before storage.